30 Freză de teșit în grade – freză din carbură solidă cu 3 caneluri

The 30 moara de teșire de grad uses solid carbide construction with straight-flute, 3-flute geometry for machining requirements where a 30° included cutter angle is specified.

Listed sizes cover Ø4–Ø12 mm cutter diameters with corresponding shank diameters and overall lengths. If the available sizes do not match the part or existing tool, OMIST can evaluate a non-standard requirement from the dimensions or drawing provided.

30 Degree Chamfer Mill Specification Options

The following dimensions represent the currently confirmed product combinations for this straight-flute 3-flute series.

Custom Dimensions

If the listed dimensions do not match the requirement, provide the required cutter diameter, diametrul tijei, lungime totală, and other available dimensional information.

A tool drawing, part drawing, or dimensional sketch can also be supplied when the cutter must match a specific part feature or existing tool.

Aplicații și selecție

When to Use a 30 Moara de teșire de grad

Choose this cutter when the part drawing or confirmed machining requirement specifies a 30° included angle and the tool dimensions match the required feature.

Typical operations include chamfering, debavurare, and edge finishing where this cutter geometry matches the part requirement.

The drawing or machining specification should determine the required angle rather than the product name alone.

Confirm the 30° Angle Reference

For this product series, 30° means the total included cutter angle.

This is especially important when replacing a tool from another supplier, because manufacturers may use different angle references in their product descriptions.

Check the angle shown on the existing tool drawing, part drawing, or dimensional sketch before using another supplier’s “30 degree” tool as a direct replacement.

Check the Required Dimensions

After confirming the angle, verifica:

• Diametrul tăietorului
• Diametrul tijei
• Lungime totală
• Spațiu de prelucrare disponibil

These dimensions should fit both the required part feature and the machining setup.

Materiale piese de prelucrat

The confirmed factory information for this product family covers:

• Oțel turnat
• Oțel călit
• Aluminiu
• Copper
• Plastics

Please state the workpiece material when requesting a quotation so OMIST can review it together with the required tool specification.

Select a Listed Size or Request a Non-Standard Tool

If one of the listed combinations matches the requirement, use the specification table to confirm the dimensions.

If the required angle or dimensions do not match the listed options, request a non-standard evaluation instead.

Caracteristici cheie

• Solid carbide construction
• 30° included cutter angle
• Straight-flute geometry
• 3-configurație flaut
• Listed cutter diameters from Ø4 to Ø12 mm
• Non-standard angle and dimension requests can be evaluated

Personalizat 30 Gradul Fabricare morii de teșire

Non-Standard Angle and Dimension Requests

The listed product on this page uses a 30° included cutter angle.

For other non-standard straight-flute chamfer cutter requirements, OMIST can evaluate angles from 30° to 160° in 5° increments, together with the required dimensional specification.

The final angle and dimensions are confirmed according to the customer requirement before production.

Custom Tools from Drawings or Dimensions

Custom evaluation is useful for replacement tools, existing machining setups, or new parts when the listed specifications do not match the required geometry.

For replacement requirements, provide the existing tool drawing or measured dimensions where possible. For a new project, send the available part drawing or dimensional information for specification review.

Informații necesare pentru o cotație

Vă rugăm să furnizați:

• Unghiul necesar
• Diametrul tăietorului
• Diametrul tijei
• Lungime totală
• Material piesa de prelucrat
• Cantitatea necesară
• Drawing or dimensional sketch, dacă este disponibil
• Any application details relevant to the requested tool specification

Dacă unele dimensiuni nu sunt încă confirmate, send the available information first for review.

FAQ

Does 30° refer to the included angle of this chamfer mill?

Da. For this OMIST product series, 30° refers to the total included cutter angle.

Este o 30 degree chamfer mill the same as a 60 moara de teșire de grad?

Nu. In this OMIST product series, the 30° and 60° models have different included cutter angles.

When replacing a tool from another supplier, confirm the angle reference on the drawing or specification.

Can I request a non-standard size or another chamfer angle?

Da. Non-standard angle and dimensional requirements can be evaluated according to the requested specification. The final tool specification is confirmed after review.

Do I need a drawing before requesting a quotation?

Nu. A drawing is helpful but is not required for the first inquiry. You can send the required angle and available dimensions first, then provide a drawing or dimensional sketch if available.

Produse conexe

If another included cutter angle is required, you can also review our 60 Moara de teșire de grad, 90 Moara de teșire de grad, 120 Moara de teșire de grad, şi 150 Moara de teșire de grad product options.

Pentru mai multe opțiuni disponibile de tăiere pentru șanfren, răsfoiește complet Mori de teșire gamă.

Solicitați o cotație pentru a 30 Moara de teșire de grad

For a listed or non-standard 30 moara de teșire de grad requirement, send the available specification or drawing to sales@cutterbest.com for review and quotation.