Tel: 0086-15907552669    E-mail: sales@cutterbest.com

About   Contact    |   

Diamond Coated Corner Radius End Mills for Graphite

End Mills/

CVD Diamond-Coated Corner Radius End Mills for Graphite

Our diamond coated corner radius end mills are designed for milling graphite electrodes and mold components. Also known as bull nose end mills, these solid carbide tools feature a CVD diamond coating and a flat cutting end with a radius where the end and side cutting edges meet.

Tool MaterialSolid carbide
CoatingCVD diamond coating
End GeometryCorner radius (bull nose)
Workpiece MaterialGraphite
Cutting DiameterØ0.5–12 mm across catalog configurations
Corner RadiusR0.05–1 mm, depending on cutting diameter
Flutes4 flutes on most configurations. The Ø0.5 mm tool and one Ø1 mm configuration have 2 flutes.
Supply OptionsStandard catalog sizes and drawing-based custom tools

Product Note

Each catalog size has a specific combination of corner radius, lengths, shank diameter and flute count. Confirm the complete configuration on your quotation before ordering.

  • Product Details
  • Technical and Order Support
  • Payment & Delivery

Selected Standard Metric Configurations

The table below lists selected sizes for our diamond coated corner radius end mills for graphite. All dimensions are in millimeters. If you need a configuration that isn’t shown, send us your required dimensions so we can check the catalog.

Cutting Dia

d

Corner Radius

R

Length of Cut

L1

Effective Length

L2

Overall Length

L

Shank Dia.

D

Flutes
0.50.05145042
10.13105042
10.13105044
1.50.1375044
20.26106044
20.26157544
30.26105044
30.210—7534
40.512—7544
6125—10064
80.325—7584
10140—200104
120.530—100124

A dash indicates that the catalog does not list a separate L2 value for that configuration.

Tool Drawing and Dimension Symbols

Corner Radius End MillDimensions

  • d is the cutting diameter, and D is the shank diameter.
  • R is the radius at the corner of the cutting end.
  • L1 is the length of cut. L2 is the effective length measured from the tool tip to the point marked on the applicable drawing. On the profile with a tapered transition, L2 ends where the taper begins.
  • L is the overall tool length.

Corner Radius End Mills for Graphite Machining

Graphite Electrodes and Mold Features

Use this geometry for flat-bottom pockets in graphite electrodes and recesses in graphite mold components where the part drawing calls for a radius between the floor and sidewall.

The tool’s corner radius R applies to that floor-to-wall transition. Check inside corners in the top view separately, where the cutter diameter and toolpath determine the achievable contour.

For guidance on choosing tools for different operations, see our graphite roughing and finishing guide. For other tool profiles, see the CVD diamond-coated end mill range.

How to Select a Standard Configuration

Match the Cutter Diameter and Corner Radius

Start with the radius specified on the part drawing. Then check that the cutting diameter fits the feature and allows the planned toolpath. Use the table to find the catalog rows that match both dimensions.

Check Length, Shank Diameter and Clearance

Choose a length of cut that covers the area the cutting edges need to machine. Check that the shank fits your holder and that the tool and holder clear the workpiece at the planned stickout. Establish usable machining depth from the setup and part geometry.

The table shows two Ø3 mm, R0.2 mm, 4-flute examples. The configuration with a 50 mm overall length has a Ø4 mm shank, a 6 mm length of cut and a 10 mm effective length. The configuration with a 75 mm overall length has a Ø3 mm shank and a 10 mm length of cut. The catalog gives no separate L2 value for the 75 mm configuration.

Frequently Asked Questions

Can I send a drawing in inches?

Yes. Keep the original units on your drawing. We can review the dimensions and confirm the metric tool configuration with you before ordering.

What if the corner radius has a tight tolerance?

Mark the required tolerance next to R on the drawing. We’ll review it for the specific configuration and confirm what we can quote.

Request a Quote For diamond coated corner radius end mills

Standard Size Inquiries

Send your required cutting diameter, corner radius and quantity. Include any fixed length, shank diameter or flute count requirements. If you need several sizes, list each size and quantity on a separate line.

Drawing-Based Custom Inquiries

Send a tool drawing or a sketch of the graphite feature. Mark the required radius and any reach or clearance constraints so we can review the tool geometry.

Request a quote for CVD diamond-coated corner radius end mills by emailing sales@cutterbest.com or chatting with us on WhatsApp.

Product Selection Support

If you’re still choosing a tool size, share the graphite grade if known, the machining operation and a sketch or photo of the feature. Include any holder or clearance restrictions that could affect the tool choice.

Custom Tool Review

We review nonstandard dimensions and tool geometry against your drawing or sample. If you need OEM marking or private-label packaging, include those requirements in your inquiry. For custom production, we confirm the final tool specification with you before manufacturing.

Payment

Your quotation or pro forma invoice (PI) sets out the payment terms and instructions.

Production Lead Time

We confirm the estimated lead time after the tool configuration and order quantity are finalized.

Packaging

We protect the cutting edges for shipment and pack the tools in an outer carton.

Shipping

We arrange international shipment according to the destination and the shipping method agreed for your order. If you use your own forwarder, share the pickup requirements when confirming the order.

Prev:

Next:

Inquiry

    PersonalBusinessDistributor

    Leave a Reply

    Leave a message